Battery Test Chamber

Home > Battery Test Chamber

BATTERY TESTING CHAMBER MODEL: ENV-11

Purpose

The Chamber is used to carry out testing of batteries. Batteries are working in various temperature and humidity conditions.  Hot Cold and Humidity Cycling and Steady State Tests at any temperature and temperature-humidity within specified limit. It meets almost all National and International Standards.

Basically this is a Hot Cold and Humidity Testing Chamber with added features related to safety in case battery leaked out and if catches fire or explode. Following are the safety features provided in the chamber:

  • N2 gas purging system (Initial purging)
  • Smoke detector
  • Smoke detector controlled CO2 gas purging system
  • Pressure based opening of the window in case of explosion
  • A 4 mm metal guide will be provided to direct exploded material based on discussion with client to avoid damage to conditioning zone.

Note:

  • We will provide solenoid operated for N2 gas and CO2 gas purging. Client has to manage pressure regulator and respective cylinders.
  • This is a general specification. Client has to decide will decide to add, avoid or control the limita like temperature and humidity as per their need to control the cost.
  • Client can also change the specifications as per their need.
  • Major test specification:

  • Temperature Testing:

-730 to +2000 C (Specify your testing range)

  • Humidity Testing:
  • Temperature: 200 to 800 C
  • Relative Humidity: 20% to 98% Rh
  • DPT: 200 to 650 C

Temperature – %Rh range covered under plot takes cares of all humidity tests and humidity cycling tests specified in IS 9000, JSS 55555 and MIL-STD-810 standards.

STANDARD SIZE OF CHAMBERS

Table-1
Final ModelWork Space (H x W x D)Static Load of SteelThermal loadNo. of Selves
ENV-11-125 Liter50 x 50 x 50 cm10 Kg20 watts1
ENV-11-450 Liter75 x 75 x 80 cm25 Kg50 watts2
ENV-11-1000 Liter100 x 100 x 100 cm50 Kg100 watts2
ENV-11-CBCustom Built (Specify H x W x D)SpecifySpecifyNot required
*    We have delivered Hot Cold & Humidity Chamber up to 10 x 4.5 x 3.5 meter size.

Standard Features:

  • Single stage refrigeration system is used up to -400 C and cascade refrigeration system is used below -400
  • Humidity Generation: Using low pressure steam generation
  • Dehumidification System: Using refrigeration system
  • Temperature sensing by Pt-100 sensor
  • % Rh sensing by capacitive RH sensor
  • Control accuracy: Better than +/- 0.5° C and +/-2% Rh (+/-10 C and +/-3% RH for Walk In Chambers)
  • Heating and cooling rate: 1° C/min to 100 C/min. Average
  • Selves are provided which can be adjustable throughout height
  • Standard Port Holes: 50 mm / 100 mm / 150 mm diameter (Specify)
  • Multilayer observation window with illumination
  • Caster wheel up to 1000 Liter models
  • Ambient condition: 10° to 45° C

Control Instrumentation Options (Select):

  • EUROTHERM Programming controller, Model-2604
  • HMI-PLC based programming controller (WATLOW or EUROTHERM)

Optional Accessories (If EUROTHERM Model-2604 is selected):

  • Two channel Paperless chart recorder
  • Two channel data logger

Major Safety Protection:

  • Independent workspace over & under temperature protection
  • Motor winding over temperature protection for semi sealed refrigeration compressors
  • High discharge and low suction pressure correction before tripping
  • Refrigeration compressor tripping abnormal high discharge and low suction pressure
  • Low water level in humidity generation system
  • Over current Relay (OLR) and MCBs are provided as required

Power Supply:

  • 415 Volt – 50 Hz – 3Φ – N – E
  • 230 Volt – 50 Hz -1Φ – E

Provide Minimum Information While Rising Inquiry to Get Precise Quotation:

  • Select final model number from Table 1.
  • Please give Chamber size (Width x Depth x Height) and Thermal load in case of Model: ENV-11-CB
  • Temperature range
  • Numbers of port holes and size (Size is mentioned above)
  • Air cooled or water cooled condenser. (We will decide for water cooled condenser for large size chambers)
  • Type of controller (Select from above)
  • Optional accessories (Select from above)
  • Specify any additional facility if needed

Electric Supply Option:

  • 415 Volt – 50 Hz – 3Φ – N – E
  • 230 Volt – 50 Hz -1Φ- E
Print Friendly, PDF & Email